Skip to content
← All guides

Overweight on delivery: why a converter should prove payload and axle loads before the build

· 8 min read

A conversion delivered over its plated gross mass or over an axle rating is the converter's problem, and the only reliable defence is arithmetic done before the first cut: weigh the bare van per axle, add the build where it will sit, add the customer's people, water and gear, and hand over with a margin of at least 5 % of the plate still free on the total and on each axle. Everything below is how to do that in a way you can show a customer, an inspector or yourself six months later.

This is physics and paperwork, not law. What happens to an overweight van on the road — fines, licence category, insurance — is set country by country, and the posts for each jurisdiction are linked at the end.

Why it is the workshop's problem

A self-builder who overloads a van has a problem with the road. A workshop that delivers one has a problem with a customer. The customer did not choose the battery bank weight or the ply thickness; you did, and you quoted them a van that does what they described. When the van shows up at a weighbridge 80 kg over, the customer's question is not “what did I pack” but “why did you sell me this”.

The fixes are expensive in the order you discover them. On paper, a heavy fitting moves forward or gets swapped for a lighter one. After delivery, it means stripping finished furniture, refunding a feature, or a re-rating (an Auflastung in German-speaking markets) that only some chassis allow and that may move the van out of the customer's licence category. The weight distribution post covers the geometry; this one covers the proof.

Step 1: weigh the base van, per axle, on arrival

Catalogue kerb weights are planning numbers. For a Ducato L3H2 the figure I plan with is 2,095 kg on a 3,500 kg plate, which leaves 1,405 kg of payload — but that is one point inside the maker's range, and the van in your yard has its own engine, options, tow bar and fuel level. Weigh it before you touch it.

TicketWhat you drive onto the plateWhat it gives you
1Front wheels onlyFront axle load
2Whole vanTotal mass
—Ticket 2 minus ticket 1Rear axle load

Write on each ticket: date, fuel level, who was in the driver's seat, and what was on board. Then read the plate (or the door-pillar label in North America) and copy the three limits next to the readings: gross mass, front axle rating, rear axle rating. That sheet is the baseline of the job. If the base van is already 80–100 kg heavier than the catalogue figure, you now know it before you have promised anything.

Step 2: estimate the build where it will sit

The build is not one number. A 100 L water tank between the axles splits its weight between them; the same mass in a rear garage behind the rear axle loads the rear axle with more than its own weight and lifts the front. Typical builds add 400–700 kg (component by component), and where that weight sits matters as much as how much of it there is.

So the estimate needs positions: every fitting, its weight, and where it sits along the wheelbase. A spreadsheet can do it if someone keeps it current through every change; a layout tool that knows the van's axle positions does it as a side effect of drawing the layout.

Step 3: add what the customer will carry

The empty, finished van is not the van that gets weighed at the roadside. Add the occupants, full water, full gas, and the gear the customer told you about: bikes, a dog, tools, a surfboard. The EN 1646-2 reserve is the floor here (10 kg per metre of length, 10 per berth, 75 per travel seat); I won't repeat it. On top of that floor, ask the customer for their real load and write it into the job: it is the number you are designing against, and you will want it in writing later. The customer spec sheet is where it goes.

Step 4: the margin, per axle

Here is the whole calculation for a Ducato L3H2 class van. The base readings, the build split and the axle ratings are an example — read your own from the tickets and the plate.

FrontRearTotal
Base van, weighed1,250 kg940 kg2,190 kg
Build, 650 kg (from the layout)260 kg390 kg650 kg
Two people in the cab120 kg30 kg150 kg
Water and gas, full45 kg70 kg115 kg
Gear, plus two bikes on a rear rack20 kg130 kg150 kg
Loaded1,695 kg1,560 kg3,255 kg
Example plate1,850 kg2,000 kg3,500 kg
Margin155 kg440 kg245 kg

245 kg free on a 3,500 kg plate is a 7 % margin: deliverable. Now the customer asks, halfway through, for a bigger lithium bank, an inverter and a second water tank — 200 kg, in the rear garage, half a metre behind the rear axle. On a 4.035 m wheelbase that adds about 225 kg to the rear axle and takes about 25 kg off the front. The total is 3,455 kg: still under the plate, and still something you could deliver. The margin is 45 kg, about 1 %, which one crate of beer or one extra passenger erases.

That is the case that ends in an argument: nothing was illegal on the day it was quoted. The weight came in through a change order that nobody priced in kilos.

Why 5 %? It is my rule, not a standard. Catalogue weights for fittings are a few percent off, the base van varies, ply varies by batch, and customers pack more than they declare. Five percent of 3,500 kg is 175 kg. Keep each axle's margin visible too: a front-wheel-drive van with a light front axle has lost traction long before it is over anything (why the front axle matters).

Step 5: weigh again before handover

Same weighbridge, same procedure, same notes on the ticket. The finished van empty of customer load should land within a few tens of kilos of base + build. If it does not, you find out on your forecourt, not theirs. File both sets of tickets with the job.

The proof pack

What I would hand over with every conversion, and keep a copy of:

  1. Base weigh tickets (front, total) with the plate limits copied next to them.
  2. The build weight estimate with the front/rear split, from the approved layout.
  3. The customer's declared load, signed.
  4. Every change order with its weight delta, not just its price.
  5. Final weigh tickets, and the margin per axle written out.

None of it is a legal document. It is evidence of what you designed, what the customer asked for, and what left your yard — which is what matters if a van comes back overweight.

Where VanPlot fits

In VanPlot every part carries a weight and sits at a position along the van, so the payload left, the EN 1646-2 reserve and the front/rear split of the added load update as the layout changes. A workshop project prints them on the Build Pack's weight page, the compliance page lists kerb, build, plated gross, payload left and reserve for the country you register in, and the change-order sheet shows what each change adds in kilos as well as in money. Customers designing on your shop page see payload and axles too, so the 200 kg garage request shows its cost before anyone asks you for it.

The Workshop licence is $329 / €299 once for the first ten workshops (then $549 / €499), with three seats (you plus two colleagues), your logo on the Build Pack, the quote page and change-order sheet (checked November 2026). For a single question, the free payload calculator does the total without an account.

Country rules

This post stays out of law on purpose. For the rules that apply to a finished camper: UK and US (DVLA body type, licence categories, where the GVWR and axle ratings are printed). In the US, a business that alters a certified vehicle takes on its certification duties under 49 CFR 567.7, and must label any changed GVWR or GAWR (eCFR, checked November 2026). For other countries, read the post in that country's language.

FAQ

What happens if a camper van conversion is overweight?

The van is over a limit printed on its own plate: the gross mass, an axle rating, or both. That shows up at a registration inspection, at a roadside weight check, or when the customer loads the van for the first trip. For the converter it is a warranty problem either way: the only fixes are taking weight out, moving it, or a re-rating where the chassis allows one, and all three cost more after delivery than at the drawing stage.

How do I weigh the front and rear axle separately at a weighbridge?

Drive only the front wheels onto the plate and take a ticket, then drive fully on and take a second one. The rear axle load is the total minus the front. Do it with the fuel level, driver and fixed equipment noted on the ticket, because every one of them moves the reading.

How much payload margin should a converter leave?

My rule, not a standard: after the EN 1646-2 reserve and the load the customer declares (water, gas, bikes, tools), at least 5 % of the plated mass should still be free — about 175 kg on a 3,500 kg van — and each axle should keep its own margin. Estimates of fittings and catalogue kerb weights are both a few percent off, and the customer always packs more than they declared.

Is the catalogue kerb weight good enough to plan a build?

For a first quote, yes. For the build, no: catalogue kerb weights are a range across engines and options, and a tow bar, second battery, larger tank or factory options can each add tens of kilos. Weigh the base van on the day it arrives, before you cut anything, and plan against that ticket.

Who is liable for an overweight conversion?

That depends on the country, the contract and who loaded the van, and this post does not answer it. In the US, 49 CFR 567.7 makes a business that alters a certified vehicle responsible for its continued conformity and requires an alterer label with any changed GVWR or GAWR. Everywhere, weigh tickets from before and after the build plus a signed load declaration are the evidence of what you delivered.

Your van is waiting. Measure it, then plan it.

In sixty seconds you'll be dragging a bed into a Ducato. Free, in your browser.

Vladimir Šterjoski

Who makes this

I'm Vladimir. I'm planning my own conversion, and none of the tools I tried could tell me whether a layout would fit or what it would do to the rear axle, so I made this one. I work on it alone. If something's wrong or missing, write to me — the address goes to my inbox.

Vladimir Šterjoski

vladimir@vanplot.comWhy I made it