Skip to content
← All guides

Converting a classic Mercedes: T1 Bremer, T2 Düdo and LN1 dimensions, payload and ex-fire-engine presets

· 8 min read

A Mercedes T1 “Bremer” gives you 1.68 m between the walls and a 2.82–3.95 m load floor on 2.8–4.6 t; a T2 “Düdo” gives 1.85 m between the walls and 3.08–4.97 m of floor on 4.6–6 t; a T2 LN1 gives 1.89 m and up to 4.93 m on 5.6–7.49 t — and only the high roofs (1.83, 1.90 and 1.94 m raw) are standing vans. Those are the numbers in VanPlot’s vehicle database since late October 2026, along with four ex-fire-engine presets (the 310 TSF, the Düdo 409 LF 8, the 608 D LF 8 and the LN1 609 D LF 8). I added them because a customer who owns an ex-fire-brigade 1987 Mercedes 310 asked for his van, then for the 409, 508 and 608.

One honest warning first: Mercedes has no data sheet online for any of these vans. Every figure below is third-party — de.wikipedia for wheelbases and weight classes, the factory load-room table and owner measurements quoted on busfreaks.de, the Ludwigsfelde works sheet for the LN1, and individual fire-brigade vehicle records for the presets. Kerb weights are estimates, so the payload column is a planning figure, not a promise. The sources are named on each van page.

The three generations

  • T1 “Bremer” (1977–95) — built in Bremen, later Düsseldorf. The 207D–210D are 2.55–2.8 t, the 307D–310 3.2–3.5 t, the 409/410 4.6 t with twin rear wheels on the mid and long wheelbase only. Three wheelbases: 3,050, 3,350 and 3,700 mm. T1 Bremer panel van · T1 Kombi / Bus
  • T2 “Düdo” (1967–86) — the Düsseldorf short-bonnet van, 406D to 613D. The 508D is 4.6–5.0 t, the 608D about 6 t, twin rear wheels. Wheelbases 2,950, 3,500 and 4,100 mm. T2 Düdo panel van · Düdo Bus
  • T2 LN1 (1986–96) — the successor, built in Ludwigsfelde: 609D to 814D, 5.6 to 7.49 t. Wheelbases 3,150, 3,700 and 4,250 mm. T2 LN1 panel van · LN1 Fensterbus

Dimensions and payload, every body

Interior width is between the walls; load floor is the length behind the cab; height is raw, floor to roof. Payload = gross weight minus the estimated kerb weight.

BodyOutside L × W × H (m)Wheelbase (mm)Load floorInside W × H (m)Kerb ≈GrossPayload ≈
T1 207D–210D short4.75 × 2.00 × 2.453,0502.82 m1.68 × 1.551,700 kg2,800 kg1,100 kg
T1 307D–310 short4.75 × 2.00 × 2.453,0502.82 m1.68 × 1.551,760 kg3,500 kg1,740 kg
T1 3xx short high roof4.75 × 2.00 × 2.753,0502.82 m1.68 × 1.831,850 kg3,500 kg1,650 kg
T1 3xx mid5.25 × 2.00 × 2.453,3503.30 m1.68 × 1.551,800 kg3,500 kg1,700 kg
T1 3xx mid high roof5.25 × 2.00 × 2.753,3503.30 m1.68 × 1.831,900 kg3,500 kg1,600 kg
T1 3xx long high roof5.90 × 2.00 × 2.753,7003.95 m1.68 × 1.832,000 kg3,500 kg1,500 kg
T1 409/410 mid high roof5.25 × 2.00 × 2.753,3503.30 m1.68 × 1.832,200 kg4,600 kg2,400 kg
T1 409/410 long high roof5.90 × 2.00 × 2.753,7003.95 m1.68 × 1.832,300 kg4,600 kg2,300 kg
Düdo 508D short5.05 × 2.10 × 2.392,9503.08 m1.85 × 1.602,600 kg4,600 kg2,000 kg
Düdo 508D mid5.99 × 2.10 × 2.393,5004.03 m1.85 × 1.602,650 kg4,600 kg1,950 kg
Düdo 508D mid high roof5.99 × 2.10 × 2.783,5004.03 m1.85 × 1.902,700 kg4,600 kg1,900 kg
Düdo 508D long high roof6.94 × 2.10 × 2.794,1004.97 m1.85 × 1.902,800 kg4,600 kg1,800 kg
Düdo 608D mid high roof5.99 × 2.10 × 2.783,5004.03 m1.85 × 1.903,600 kg5,990 kg2,390 kg
Düdo 608D long high roof6.94 × 2.10 × 2.794,1004.97 m1.85 × 1.903,700 kg5,990 kg2,290 kg
LN1 609D short5.45 × 2.18 × 2.563,1503.26 m1.89 × 1.792,950 kg5,600 kg2,650 kg
LN1 709D/711D mid high roof6.33 × 2.18 × 2.723,7004.14 m1.89 × 1.943,100 kg6,600 kg3,500 kg
LN1 809D/811D long high roof6.88 × 2.18 × 2.724,2504.69 m1.89 × 1.943,300 kg7,490 kg4,190 kg
LN1 809D/814D long Maxi7.21 × 2.18 × 2.724,2504.93 m1.89 × 1.943,400 kg7,490 kg4,090 kg

The LN1 short length (5.45 m) is the published minimum for the range. The Kombi, Düdo Bus and LN1 Fensterbus share the panel van’s body sizes; the planner draws their window rows.

What fits — and what doesn’t

  • The T1 is a lengthways-bed van. 1.68 m between the walls is shorter than a standard 1.90 m mattress, so a crosswise bed is out; the bed runs along a wall or across the back as a short-length single. The short T1 (2.82 m of floor) holds a bed and a small kitchen; the long one (3.95 m) is where a fixed bed, a kitchen and a seat with a table all fit. Which vans you can sleep across runs the same width check for modern vans.
  • The Düdo is wide between the walls, narrow between the arches. 1.85 m is more than a modern large van, but the wheelhouses leave 1.49 m. A crosswise bed works above the arches, not between them. With 4.97 m of floor on the long 508D, a fixed bed plus a full kitchen and a dinette are realistic.
  • The LN1 is the biggest and the heaviest. 1.89 m wide and up to 4.93 m of floor — space for a rear garage under the bed — on a chassis plated at 5.6 to 7.49 t.
  • Standing height needs the high roof. By the raw height plus 10 cm rule, a high-roof T1 (1.83 m) stands someone up to about 1.73 m, a high-roof Düdo (1.90) to 1.80 m, a high-roof LN1 (1.94) to 1.84 m. The normal-roof versions are sit-down vans.
  • Twin rear wheels mean bigger wheelhouses. The 409/410, 608D and the LN1 run twin rear tyres; the database draws the twin pair and a deeper arch box, which is what eats into a crosswise bed or a garage floor.

The ex-fire-engine presets

Ex-brigade Mercedes are a common start for a German build (Feuerwehr Wohnmobil Umbau), but every brigade’s body came from a different coachbuilder (Ziegler, Metz, Bachert, Schlingmann, Thoma), so there is no “typical” size. The four presets on the Start from a chassis step each carry one documented fleet vehicle’s figures; the box interiors are estimates. Treat them as a starting point and type in your own measurements.

PresetBaseOutside L × W × H (m)Wheelbase (mm)Space to build in (est.)KerbGross
310 KA TSF (Ziegler)T1 crew panel van, 6 seats5.45 × 1.98 × 2.403,3502.40 × 1.68 × 1.55 behind the crew row2,290 kg3,500 kg
409 LF 8 (Bachert / Metz)T2 Düdo crew cab + box5.95 × 2.15 × 2.652,9502.40 × 1.90 × 1.80 box2,950 kg5,200 kg
608 D LF 8 (Metz)T2 Düdo crew cab + box6.37 × 2.16 × 2.802,9502.60 × 1.95 × 1.95 box3,590 kg6,500 kg
609 D LF 8 (Thoma)T2 LN1 crew cab + box6.40 × 2.16 × 2.703,7002.60 × 1.90 × 1.85 box3,700 kg5,600 kg

Two things the presets make obvious. The 310 TSF is a panel van, not a box truck: the crew sits behind the cab inside the van, with sliding doors on both sides, so you build in 2.40 m of floor behind a seat row — and it is the only one of the four that stays at 3.5 t. The LF 8s are crew cabs with a separate box: the box is 2.4–2.6 m long, so the bed, kitchen and seating all have to fit in roughly the floor of a short panel van, and the roller-shutter lockers in its sides are wall you cannot use for windows without cutting.

Before you buy one

  • Weigh it. The kerb weights here are estimates over the bare chassis or a single listing; a 40-year-old van with a heavy body, rust repairs or brigade fittings can be hundreds of kilos off. Ten minutes at a public weighbridge replaces every number in the payload column. The payload calculator works from your own figure.
  • Read the plate, not the badge. Weight classes overlap: some 508Ds were derated to 3.49 t, and an LN1 can be anything from 3.49 to 7.49 t. Everything above 3,500 kg is outside a category B licence for most drivers in the EU and UK — the payload guide covers the rules and how much a build weighs.
  • Check the axle loads with the build in, not just the total. A heavy water tank or battery bank behind the rear axle on a long wheelbase loads that axle hard. Your van’s permitted axle loads are on its registration papers; where the weight sits explains the check.

Plan it before you buy it

Pick Mercedes-Benz → T1 Bremer, T2 Düdo or T2 LN1 in the planner, or Custom van body → Start from a chassis for an ex-fire engine, and the 3D floor, walls, roof and payload readout use the figures above. If your van measures differently, the custom body takes your own numbers. The full list of 53 vehicles and 277 variants is on the vans page.

FAQ

How big is a Mercedes T1 Bremer inside?

About 1.68 m between the walls on every body. The load floor is 2.82 m on the short 3,050 mm wheelbase, 3.30 m on the 3,350 mm and 3.95 m on the 3,700 mm wheelbase. The normal roof gives 1.55 m of raw headroom, the high roof 1.83 m. Outside it is 2.00 m wide and 4.75, 5.25 or 5.90 m long.

Can you stand up in a Düdo or an LN1?

Only with the high roof. A high-roof T2 Düdo has about 1.90 m raw inside and a high-roof LN1 about 1.94 m. After a 6–7 cm floor and ceiling build-up that stands someone up to roughly 1.80 m in the Düdo and 1.84 m in the LN1. The normal-roof Düdo (1.60 m) and the short normal-roof LN1 (1.785 m) are sit-down vans, and so is a normal-roof T1 (1.55 m).

Is the ex-fire-brigade 409 a T1 or a T2?

Mercedes built a 409 D in the T1 range, but almost every ex-fire 409 for sale is a T2 Düdo 409 — the petrol LF 8 built 1974–82 with a crew cab and a box with roller-shutter lockers. That is how the VanPlot preset models it: about 5.95 m long, 2.15 m wide, 2.65 m tall, 5.2 t gross.

Which classic Mercedes stays under 3.5 tonnes?

The T1 207D–310 range is plated at 2.8–3.5 t and the 310 KA TSF fire van at 3.5 t. The T1 409/410 is 4.6 t, the Düdo 508D 4.6–5.0 t, the 608D about 6 t and the LN1 5.6–7.49 t. Some 508Ds were derated to 3.49 t — check the registration document, not the model badge.

Where do these figures come from?

Mercedes publishes no data sheet online for any of these vans. Every figure is third-party: de.wikipedia for wheelbases and weight classes, the factory load-room table and owner measurements quoted on busfreaks.de, the Ludwigsfelde LN1 works sheet, and individual fire-brigade vehicle records for the presets. Kerb weights are estimates. Weigh your own van before you trust a payload figure.

Your van is waiting. Measure it, then plan it.

In sixty seconds you'll be dragging a bed into a Ducato. Free, in your browser.

Vladimir Šterjoski

Who makes this

I'm Vladimir. I'm planning my own conversion, and none of the tools I tried could tell me whether a layout would fit or what it would do to the rear axle, so I made this one. I work on it alone. If something's wrong or missing, write to me — the address goes to my inbox.

Vladimir Šterjoski

vladimir@vanplot.comWhy I made it