Skip to content
← All vans

Mercedes-Benz T2 LN1 panel van camper conversion

The T2 LN1 panel van comes in 4 variants in the planner, with cargo areas from 3.26 m to 4.93 m long inside and payloads up to about 4,190 kg. Drivetrains: RWD.

Also sold as Mercedes 609D 709D 711D 809D 811D 814D, T2 neu, Vario Vorgänger, Düdo LN1, Dudo LN1.

Yes — you can stand up in a Mercedes-Benz T2 LN1 panel van from the 709D / 711D Mittel Hochdach roof up: 1.94 m floor-to-headliner, about 1.87 m after a typical 7 cm floor and ceiling build-up, which stands an adult up to about 1.80 m.

Interior dimensions by variant

VariantDriveInterior L × W × HPayload ≈WheelbaseExt. height
609D KurzRWD3.26 × 1.89 × 1.78 m2,650 kg3.15 m2.56 m
709D / 711D Mittel HochdachRWD4.14 × 1.89 × 1.94 m3,500 kg3.70 m2.72 m
809D / 811D Lang HochdachRWD4.69 × 1.89 × 1.94 m4,190 kg4.25 m2.72 m
809D / 814D Lang Maxi HochdachRWD4.93 × 1.89 × 1.94 m4,090 kg4.25 m2.72 m

Interior figures are between the walls and floor-to-headliner, derived from manufacturer specs and calibrated against published cargo dimensions. Payload ≈ gross weight minus kerb weight — it varies with engine and options, so treat it as a planning guide.

What fits

  • Standing: after a typical floor and ceiling build-up (~7 cm), the T2 LN1 panel van 709D / 711D Mittel Hochdach leaves about 1.87 m of headroom.
  • Bed across: at 1.89 m between the walls, the T2 LN1 panel van 609D Kurz takes a standard 1.86 m mattress transversely — the layout that frees the most floor.
  • Parking: every variant is over 2.0 m tall outside — underground garages and most height barriers are out.

Payload budget

Depending on variant, the T2 LN1 panel van carries roughly 2,650 kg to 4,190 kg of conversion, gear, water and people before hitting the gross weight limit. A typical full build lands between 400 and 700 kg before you pack — weigh the plan before you cut.

Check your numbers in the payload calculator →

Mercedes-Benz T2 LN1 panel van camper layouts and floor plans

The gallery has no layout on the Mercedes-Benz T2 LN1 panel van yet. Its floor plans are drawn on other vans; the planner starts a T2 LN1 panel van with its real interior dimensions and you draw your own layout.

Same van, different badge

These vans are built on the same body as the T2 LN1 panel van — the dimensions and layout advice carry over one-to-one:

Frequently asked

How long is the T2 LN1 panel van inside?

The cargo area runs from 3.26 m in the shortest variant to 4.93 m in the longest, measured from the bulkhead to the rear doors.

Can I stand up in a Mercedes-Benz T2 LN1 panel van?

Yes — you can stand up in a Mercedes-Benz T2 LN1 panel van from the 709D / 711D Mittel Hochdach roof up: 1.94 m floor-to-headliner, about 1.87 m after a typical 7 cm floor and ceiling build-up, which stands an adult up to about 1.80 m. By roof height — 609D Kurz: 1.79 m raw, ~1.72 m finished — sit-down only; 709D / 711D Mittel Hochdach: 1.94 m raw, ~1.87 m finished — stands a 1.80 m adult; 809D / 811D Lang Hochdach: 1.94 m raw, ~1.87 m finished — stands a 1.80 m adult; 809D / 814D Lang Maxi Hochdach: 1.94 m raw, ~1.87 m finished — stands a 1.80 m adult. Rule of thumb: you need a raw interior height of your own height plus 10 cm.

How much payload does a T2 LN1 panel van have for a conversion?

Roughly 2,650 kg to 4,190 kg depending on variant and engine — gross weight minus kerb weight. The build, water, gear and passengers all come out of that number.

Are there ready-made Mercedes-Benz T2 LN1 panel van camper layouts or floor plans?

Not in the gallery yet. The planner has every T2 LN1 panel van variant with its real interior, so you can draw the floor plan in an empty van or start from a template.

Which vans are the same as the T2 LN1 panel van?

The T2 LN1 panel van shares its body and dimensions with: Mercedes-Benz T2 LN1 Fensterbus, Mercedes 609D 709D 711D 809D 811D 814D, T2 neu, Vario Vorgänger, Düdo LN1, Dudo LN1, Fensterbus, Gruppenkraftwagen, GruKW, O 609, Mercedes 711D Bus, THW Bus.

Figures derived from manufacturer specifications; interior dimensions calibrated against published cargo volumes. Always verify against your actual vehicle — model years differ.

Plan your T2 LN1 panel van in 3D

Every variant on this page is in the planner with real wheel arches, wall taper and door apertures. Place the bed, watch the payload — before you buy the van.

Vladimir Šterjoski

Who makes this

I'm Vladimir. I'm planning my own conversion, and none of the tools I tried could tell me whether a layout would fit or what it would do to the rear axle, so I made this one. I work on it alone. If something's wrong or missing, write to me — the address goes to my inbox.

Vladimir Šterjoski

vladimir@vanplot.comWhy I made it