Skip to content
← All vans

Mercedes-Benz T1 Bremer Kombi / Bus camper conversion

The T1 Bremer Kombi / Bus comes in 3 variants in the planner, with cargo areas from 3.30 m to 3.95 m long inside and payloads up to about 1,700 kg. Drivetrains: RWD.

Also sold as Bremer Kombi, Mercedes 308 Bus, T1 Bus.

Yes — you can stand up in a Mercedes-Benz T1 Bremer Kombi / Bus from the Mittel Hochdach roof up: 1.83 m floor-to-headliner, about 1.76 m after a typical 7 cm floor and ceiling build-up, which stands an adult up to about 1.70 m.

Interior dimensions by variant

VariantDriveInterior L × W × HPayload ≈WheelbaseExt. height
MittelRWD3.30 × 1.68 × 1.55 m1,700 kg3.35 m2.45 m
Mittel HochdachRWD3.30 × 1.68 × 1.83 m1,600 kg3.35 m2.75 m
Lang HochdachRWD3.95 × 1.68 × 1.83 m1,500 kg3.70 m2.75 m

Interior figures are between the walls and floor-to-headliner, derived from manufacturer specs and calibrated against published cargo dimensions. Payload ≈ gross weight minus kerb weight — it varies with engine and options, so treat it as a planning guide.

What fits

  • Standing: the tallest variant has 1.83 m inside; after a ~7 cm floor and ceiling build-up you sit, crouch or pop the top — this is not a stand-up van.
  • Bed across: the widest variant measures 1.68 m between the walls — short of a 1.86 m mattress, so plan the bed lengthwise or add wheel-box flares.
  • Parking: every variant is over 2.0 m tall outside — underground garages and most height barriers are out.

Payload budget

Depending on variant, the T1 Bremer Kombi / Bus carries roughly 1,500 kg to 1,700 kg of conversion, gear, water and people before hitting the gross weight limit. A typical full build lands between 400 and 700 kg before you pack — weigh the plan before you cut.

Check your numbers in the payload calculator →

Mercedes-Benz T1 Bremer Kombi / Bus camper layouts and floor plans

The gallery has no layout on the Mercedes-Benz T1 Bremer Kombi / Bus yet. Its floor plans are drawn on other vans; the planner starts a T1 Bremer Kombi / Bus with its real interior dimensions and you draw your own layout.

Same van, different badge

These vans are built on the same body as the T1 Bremer Kombi / Bus — the dimensions and layout advice carry over one-to-one:

Frequently asked

How long is the T1 Bremer Kombi / Bus inside?

The cargo area runs from 3.30 m in the shortest variant to 3.95 m in the longest, measured from the bulkhead to the rear doors.

Can I stand up in a Mercedes-Benz T1 Bremer Kombi / Bus?

Yes — you can stand up in a Mercedes-Benz T1 Bremer Kombi / Bus from the Mittel Hochdach roof up: 1.83 m floor-to-headliner, about 1.76 m after a typical 7 cm floor and ceiling build-up, which stands an adult up to about 1.70 m. By roof height — Mittel: 1.55 m raw, ~1.48 m finished — sit-down only; Mittel Hochdach: 1.83 m raw, ~1.76 m finished — stands a 1.70 m adult; Lang Hochdach: 1.83 m raw, ~1.76 m finished — stands a 1.70 m adult. Rule of thumb: you need a raw interior height of your own height plus 10 cm.

How much payload does a T1 Bremer Kombi / Bus have for a conversion?

Roughly 1,500 kg to 1,700 kg depending on variant and engine — gross weight minus kerb weight. The build, water, gear and passengers all come out of that number.

Are there ready-made Mercedes-Benz T1 Bremer Kombi / Bus camper layouts or floor plans?

Not in the gallery yet. The planner has every T1 Bremer Kombi / Bus variant with its real interior, so you can draw the floor plan in an empty van or start from a template.

Which vans are the same as the T1 Bremer Kombi / Bus?

The T1 Bremer Kombi / Bus shares its body and dimensions with: Mercedes-Benz T1 Bremer panel van, Bremer Kombi, Mercedes 308 Bus, T1 Bus, Bremer Transporter, Mercedes 207D 307D 310 409 410, MB 310, TN, Feuerwehr TSF, Firetruck T1, Brandweer T1.

Figures derived from manufacturer specifications; interior dimensions calibrated against published cargo volumes. Always verify against your actual vehicle — model years differ.

Plan your T1 Bremer Kombi / Bus in 3D

Every variant on this page is in the planner with real wheel arches, wall taper and door apertures. Place the bed, watch the payload — before you buy the van.

Vladimir Šterjoski

Who makes this

I'm Vladimir. I'm planning my own conversion, and none of the tools I tried could tell me whether a layout would fit or what it would do to the rear axle, so I made this one. I work on it alone. If something's wrong or missing, write to me — the address goes to my inbox.

Vladimir Šterjoski

vladimir@vanplot.comWhy I made it