Mercedes-Benz T1 Bremer Kombi / Bus Lang Hochdach RWD camper conversion dimensions
The Mercedes-Benz T1 Bremer Kombi / Bus Lang Hochdach RWD measures 3.95 m long, 1.68 m wide and 1.83 m high inside — bulkhead to rear doors, between the walls, floor to headliner — on a 3.70 m wheelbase. Kerb weight 2,000 kg, payload about 1,500 kg.
Dimensions
- Cargo length
- 3.95 m
- Interior width
- 1.68 m
- Interior height
- 1.83 m
- Wheelbase
- 3.70 m
- Exterior length
- 5.90 m
- Exterior width
- 2.00 m
- Exterior height
- 2.75 m
- Kerb weight
- 2,000 kg
- Payload ≈
- 1,500 kg
- Gross weight
- 3,500 kg
Interior figures are between the walls and floor-to-headliner, derived from manufacturer specs and calibrated against published cargo dimensions. Payload ≈ gross weight minus kerb weight — it varies with engine and options, so treat it as a planning guide.
- Dimensions source: Mercedes-Benz T 1 (de.wikipedia: weight classes, wheelbases, track) + the factory load-room table and owner measurements quoted on busfreaks.de (threads 39964, 26567, 76504, 40530) (third-party table — no maker document found) · checked Oct 2026
- Door openings: estimate — the maker publishes no opening; measure your van · checked Oct 2026
What fits
- Standing: 1.83 m floor-to-headliner, about 1.76 m after a typical 7 cm floor and ceiling build-up — stands an adult up to about 1.70 m.
- Bed across: 1.68 m between the walls, about 1.62 m after 6 cm of finished walls — too short for an adult across; plan the bed lengthwise or add wheel-box flares.
- Parking: 2.75 m tall outside — over 2.0 m, so underground garages and most height barriers are out (French motorway class 2).
- Payload: about 1,500 kg — 3,500 kg gross minus 2,000 kg kerb. After a typical 600 kg build and the EN 1646-2 two-person reserve of 154 kg, roughly 746 kg is left for water, gear and people.
Mercedes-Benz T1 Bremer Kombi / Bus Lang Hochdach layouts and floor plans
The gallery has no layout on the Mercedes-Benz T1 Bremer Kombi / Bus yet. Its floor plans are drawn on other vans; the planner starts a T1 Bremer Kombi / Bus with its real interior dimensions and you draw your own layout.
Other T1 Bremer Kombi / Bus variants
All 3 T1 Bremer Kombi / Bus variants in the planner — same body, different length, roof or drivetrain:
| Variant | Drive | Interior L × W × H | Payload ≈ | Wheelbase | Ext. height |
|---|---|---|---|---|---|
| Mittel | RWD | 3.30 × 1.68 × 1.55 m | 1,700 kg | 3.35 m | 2.45 m |
| Mittel Hochdach | RWD | 3.30 × 1.68 × 1.83 m | 1,600 kg | 3.35 m | 2.75 m |
| Lang Hochdach | RWD | 3.95 × 1.68 × 1.83 m | 1,500 kg | 3.70 m | 2.75 m |
Check the numbers
Frequently asked
What are the interior dimensions of a Mercedes-Benz T1 Bremer Kombi / Bus Lang Hochdach RWD?
3.95 m long, 1.68 m wide and 1.83 m high inside — bulkhead to rear doors, between the walls, floor to headliner. Outside it is 5.90 m × 2.00 m × 2.75 m on a 3.70 m wheelbase.
Can I stand up in a Mercedes-Benz T1 Bremer Kombi / Bus Lang Hochdach RWD?
1.83 m floor-to-headliner, about 1.76 m after a typical 7 cm floor and ceiling build-up — stands an adult up to about 1.70 m. Rule of thumb: you need a raw interior height of your own height plus 10 cm.
Can I sleep across a Mercedes-Benz T1 Bremer Kombi / Bus Lang Hochdach RWD?
1.68 m between the walls, about 1.62 m after 6 cm of finished walls — too short for an adult across; plan the bed lengthwise or add wheel-box flares.
How much payload does a Mercedes-Benz T1 Bremer Kombi / Bus Lang Hochdach RWD have?
About 1,500 kg: 3,500 kg gross weight minus 2,000 kg kerb weight. It varies with engine and options, so treat it as a planning guide — the build, water, gear and passengers all come out of that number.
Figures derived from manufacturer specifications; interior dimensions calibrated against published cargo volumes. Always verify against your actual vehicle — model years differ.
Plan your T1 Bremer Kombi / Bus Lang Hochdach in 3D
This exact variant is in the planner with its real wheel arches, wall taper and door apertures. Place the bed, watch the payload — before you buy the van.
Who makes this
I'm Vladimir. I'm planning my own conversion, and none of the tools I tried could tell me whether a layout would fit or what it would do to the rear axle, so I made this one. I work on it alone. If something's wrong or missing, write to me — the address goes to my inbox.
Vladimir Šterjoski