Skip to content
← All guides

Panel van vs box truck or cutaway camper: what you gain in width and lose in weight

· 7 min read

A box body on a chassis cab or cutaway gives you 20–55 cm more width than a panel van (2.08–2.34 m against 1.78–1.87 m), vertical walls and a floor with no wheel arches — enough to sleep across it at any height — but it adds roughly 700 kg of box, about half a metre of overall height (3.1–3.3 m against 2.5–2.8 m) and, above 3,500 kg, a bigger driving licence in the EU. That is the trade. Which side of it wins depends on whether your layout is limited by width or by weight, and the numbers below are what decide it.

All figures come from the vehicle database behind the planner. The panel vans are maker figures, re-read against the makers’ documents in September 2026. The chassis figures for the box trucks (wheelbase, gross weight, cab) are the maker’s too; the boxes themselves are coachbuilt, so their inside dimensions and the built kerb weight are estimates from typical bodies sold on each chassis, and are labelled that way on each van page.

The table: panel van against box body

VehicleBodyInside widthInside heightFloor lengthOutside heightGrossPayload
Fiat Ducato L3H2 FWDpanel1.87 m1.93 m3.71 m2.52 m3,500 kg1,405 kg
Fiat Ducato L4H2 FWDpanel1.87 m1.93 m4.07 m2.52 m3,500 kg1,265 kg
Mercedes Sprinter L3H2 RWDpanel1.79 m2.01 m4.31 m2.62 m3,500 kg1,095 kg
Ford Transit L4H3 RWDpanel1.78 m2.03 m4.22 m2.78 m3,500 kg1,107 kg
Iveco Daily L4H2 (panel van)panel1.80 m1.90 m4.68 m2.66 m3,500 kg940 kg
Ford Transit 350 cutaway, 14 ft boxbox2.08 m2.13 m4.19 m3.10 m4,699 kg1,749 kg
Ford Transit 350HD cutaway, 16 ft boxbox2.08 m2.13 m4.90 m3.10 m4,990 kg1,890 kg
Ford E-350 cutaway, 14 ft boxbox2.34 m2.13 m4.19 m3.20 m5,670 kg2,220 kg
Iveco Daily 70C chassis cab, 4.5 m boxbox2.24 m2.09 m4.50 m3.30 m7,000 kg3,800 kg

Payload is gross weight minus kerb weight as the planner uses it — before passengers, water, fuel reserve and the build itself. For the box rows the kerb already includes the box shell.

What you gain: width, square walls, a flat floor

Width. A panel van’s width is set by the pressed steel body, and the widest one, the Ducato family, is 1.87 m between the bare walls. The transverse-bed table shows what that means: after 6 cm of insulation and panels, 1.81 m finished — marginal for a 1.80 m sleeper, and every other large van is narrower. A box is built to the chassis, not to a steel pressing. With the same 6 cm taken off, the Transit 350 cutaway box is about 2.02 m finished, the Daily 70C 2.18 m and the E-350 cube 2.28 m. A 2.00 m mattress fits across the last two; a 1.95 m person sleeps across any of them.

Square walls. Panel van walls lean in as they rise. The planner models that tumblehome as 10–13 cm of usable width lost per side at roof height on a Sprinter, Transit, Crafter or Master, and 3 cm on a Ducato. A box wall is vertical, so an overhead cabinet is as deep at the top as the counter under it, and a wardrobe is a rectangle instead of a wedge.

No arches in the floor. On a box body the floor rides above the wheels. A panel van carries its rear wheel arches inside the cargo bay — the between-the-arches table has the figures — and every bed, garage and tank has to be planned around them. In a box the floor is one flat rectangle from the front wall to the doors.

What you lose: weight, height, licence

Box weight. A box is a second body. On the Iveco Daily 70C rows in the database the kerb is the maker’s chassis-cab figure (2,445–2,513 kg) plus about 700 kg for the box shell — my estimate from built examples, and the number varies with the coachbuilder, the panel type and the floor. That 700 kg is before insulation, furniture or water, which add another 400–700 kg in a typical build.

The box trucks above still show more payload than the panel vans because they sit on heavier chassis: 4.7–7.0 t gross against 3.5 t. If you want a box and a 3.5 t limit, the box weight comes straight out of a payload that is already the tightest number in the build. I do not have a sourced 3.5 t chassis-cab-plus-box row in the database, so I will not print one — ask the coachbuilder for a weighed figure, not a catalogue one, and compare it against the under-3,500 kg table.

Height. The box floor sits on top of the chassis frame. In the planner a panel van’s cargo floor is 0.62 m off the ground, a cutaway box floor 0.9 m and a truck box floor 1.1 m. Add 2.1 m of standing room and a roof, and the box rows land at 3.10–3.30 m tall. The tallest panel van above, the Transit L4H3, is 2.78 m. Under 3 m with standing height inside is a target the boxes in the database do not hit; it takes a low-floor chassis or a lower interior. Every car park barrier, ferry height band and low bridge sees the difference, and so does the wind: a flat-fronted box 3 m tall is a sail. The 2 m barrier post runs the low end of the same question.

Licence. In the EU the car licence (category B, Directive 2006/126/EC) ends at 3,500 kg gross. The Transit 350 cutaway (4,699–4,990 kg) and the Daily 70C (7,000 kg) need category C1. In the US no commercial licence is needed below 26,001 lb (about 11.8 t) gross, which is why cutaways are a common base there. These are the only licence facts in this post; check your own country’s rules for tolls, speed limits and inspections above 3.5 t before buying.

The cab. On a box body the cab is its own unit, with a gap to the box. Walking from the driver’s seat into the living space needs a cut-through in both the cab and the box front wall, joined by a flexible seal. In a panel van the cab is already part of the room, and swivelled front seats become the lounge.

Which one, by layout

  • You need to sleep across, you are over 1.80 m, and you drive a 3.5 t van: a Ducato-family panel van with wall flares is the only path that keeps the licence; see the stand-up and sleep-across tables.
  • You need a 2.00 m bed across, a fixed shower and a garage, and have C1 (or live in the US): a box on a 4.7–7 t chassis gives you a rectangle 2.1–2.3 m wide and the payload to fill it.
  • You park in cities or under barriers: panel van. A box is a 3 m-plus vehicle every day of the trip.

Check it on your own layout

Pick a Daily 70C or Transit 350 cutaway in the planner and the bay is a flat box with square walls; pick a Ducato or Sprinter and the arches and leaning walls are back. Place the same bed, kitchen and tanks in both and the payload bar shows which one runs out first. If your box comes from a coachbuilder, open any vehicle with Edit as custom van and type in the box’s inside dimensions and the weighed kerb. I have not built a van yet; this is the comparison I would run before buying either.

FAQ

Is a box truck wider inside than a panel van?

Yes, by 20–55 cm. Large panel vans are 1.78–1.87 m between the bare walls, and the walls lean in towards the roof. A Ford Transit 350 cutaway with a typical 86 in box is about 2.08 m inside, an Iveco Daily 70C box about 2.24 m and an E-350 / E-450 cube about 2.34 m — with vertical walls and no wheel arches in the floor.

Does the box body eat the payload?

The box shell itself weighs roughly 700 kg on an Iveco Daily 70C (my estimate from the chassis-cab kerb weight and built examples). The box trucks still carry more because they sit on heavier chassis: about 1.75–1.89 t of payload on a Transit 350 cutaway (4.7–5.0 t gross) and about 3.8 t on a 7 t Daily 70C, against 0.9–1.4 t on a 3.5 t panel van.

Can a box camper stay under 3 m tall?

Not with standing height inside, in the examples I have. The floor of a box sits on top of the chassis frame — about 0.9 m off the ground on a cutaway and 1.1 m on a truck box, against 0.62 m in a panel van — so the cutaways come out at about 3.10–3.20 m and the Daily 70C at about 3.30 m with 2.09–2.13 m inside. A high-roof panel van is 2.52–2.78 m tall.

Can I drive a box-body camper on a car licence?

In the EU the car licence (category B, Directive 2006/126/EC) covers vehicles up to 3,500 kg gross. A Transit 350 cutaway (4,699–4,990 kg) or a Daily 70C (7,000 kg) needs category C1. In the US no commercial licence is needed below 26,001 lb gross, which covers every cutaway mentioned here. Check your own country's rules before buying.

Can I plan a box or cutaway conversion in VanPlot?

Yes. The Ford Transit 350 cutaway, Ford E-350 / E-450 cutaway and Iveco Daily 70C chassis cab are in the vehicle picker with a typical box, and any panel van can be edited as a custom vehicle with your coachbuilder's box dimensions. The box figures are labelled as estimates, because every coachbuilt box is different.

Your van is waiting. Measure it, then plan it.

In sixty seconds you'll be dragging a bed into a Ducato. Free, in your browser.

Vladimir Šterjoski

Who makes this

I'm Vladimir. I'm planning my own conversion, and none of the tools I tried could tell me whether a layout would fit or what it would do to the rear axle, so I made this one. I work on it alone. If something's wrong or missing, write to me — the address goes to my inbox.

Vladimir Šterjoski

vladimir@vanplot.comWhy I made it