Skip to content

Mercedes-Benz T1 Bremer panel van 207D–210D Kurz RWD camper conversion dimensions

The Mercedes-Benz T1 Bremer panel van 207D–210D Kurz RWD measures 2.82 m long, 1.68 m wide and 1.55 m high inside — bulkhead to rear doors, between the walls, floor to headliner — on a 3.05 m wheelbase. Kerb weight 1,700 kg, payload about 1,100 kg.

Dimensions

Cargo length
2.82 m
Interior width
1.68 m
Interior height
1.55 m
Wheelbase
3.05 m
Exterior length
4.75 m
Exterior width
2.00 m
Exterior height
2.45 m
Kerb weight
1,700 kg
Payload ≈
1,100 kg
Gross weight
2,800 kg

Interior figures are between the walls and floor-to-headliner, derived from manufacturer specs and calibrated against published cargo dimensions. Payload ≈ gross weight minus kerb weight — it varies with engine and options, so treat it as a planning guide.

What fits

  • Standing: 1.55 m floor-to-headliner, about 1.48 m after a typical 7 cm floor and ceiling build-up — a sit-down van; adults crouch or pop the top.
  • Bed across: 1.68 m between the walls, about 1.62 m after 6 cm of finished walls — too short for an adult across; plan the bed lengthwise or add wheel-box flares.
  • Parking: 2.45 m tall outside — over 2.0 m, so underground garages and most height barriers are out (French motorway class 2).
  • Payload: about 1,100 kg — 2,800 kg gross minus 1,700 kg kerb. After a typical 600 kg build and the EN 1646-2 two-person reserve of 143 kg, roughly 357 kg is left for water, gear and people.

Mercedes-Benz T1 Bremer panel van 207D–210D Kurz layouts and floor plans

The gallery has no layout on the Mercedes-Benz T1 Bremer panel van yet. Its floor plans are drawn on other vans; the planner starts a T1 Bremer panel van with its real interior dimensions and you draw your own layout.

Other T1 Bremer panel van variants

All 8 T1 Bremer panel van variants in the planner — same body, different length, roof or drivetrain:

VariantDriveInterior L × W × HPayload ≈WheelbaseExt. height
207D–210D KurzRWD2.82 × 1.68 × 1.55 m1,100 kg3.05 m2.45 m
307D–310 KurzRWD2.82 × 1.68 × 1.55 m1,740 kg3.05 m2.45 m
307D–310 Kurz HochdachRWD2.82 × 1.68 × 1.83 m1,650 kg3.05 m2.75 m
MittelRWD3.30 × 1.68 × 1.55 m1,700 kg3.35 m2.45 m
Mittel HochdachRWD3.30 × 1.68 × 1.83 m1,600 kg3.35 m2.75 m
Lang HochdachRWD3.95 × 1.68 × 1.83 m1,500 kg3.70 m2.75 m
409 / 410 Mittel HochdachRWD3.30 × 1.68 × 1.83 m2,400 kg3.35 m2.75 m
409 / 410 Lang HochdachRWD3.95 × 1.68 × 1.83 m2,300 kg3.70 m2.75 m
Every Mercedes-Benz T1 Bremer panel van variant compared →What does “207D–210D Kurz” actually mean? →

Check the numbers

Frequently asked

What are the interior dimensions of a Mercedes-Benz T1 Bremer panel van 207D–210D Kurz RWD?

2.82 m long, 1.68 m wide and 1.55 m high inside — bulkhead to rear doors, between the walls, floor to headliner. Outside it is 4.75 m × 2.00 m × 2.45 m on a 3.05 m wheelbase.

Can I stand up in a Mercedes-Benz T1 Bremer panel van 207D–210D Kurz RWD?

1.55 m floor-to-headliner, about 1.48 m after a typical 7 cm floor and ceiling build-up — a sit-down van; adults crouch or pop the top. Rule of thumb: you need a raw interior height of your own height plus 10 cm.

Can I sleep across a Mercedes-Benz T1 Bremer panel van 207D–210D Kurz RWD?

1.68 m between the walls, about 1.62 m after 6 cm of finished walls — too short for an adult across; plan the bed lengthwise or add wheel-box flares.

How much payload does a Mercedes-Benz T1 Bremer panel van 207D–210D Kurz RWD have?

About 1,100 kg: 2,800 kg gross weight minus 1,700 kg kerb weight. It varies with engine and options, so treat it as a planning guide — the build, water, gear and passengers all come out of that number.

Figures derived from manufacturer specifications; interior dimensions calibrated against published cargo volumes. Always verify against your actual vehicle — model years differ.

Plan your T1 Bremer panel van 207D–210D Kurz in 3D

This exact variant is in the planner with its real wheel arches, wall taper and door apertures. Place the bed, watch the payload — before you buy the van.

Vladimir Šterjoski

Who makes this

I'm Vladimir. I'm planning my own conversion, and none of the tools I tried could tell me whether a layout would fit or what it would do to the rear axle, so I made this one. I work on it alone. If something's wrong or missing, write to me — the address goes to my inbox.

Vladimir Šterjoski

vladimir@vanplot.comWhy I made it