Campervan floor thickness: what ply and insulation cost in headroom and weight
· 7 min read
A typical campervan floor — 20 mm XPS, 12 mm plywood and vinyl — is 34 mm thick and weighs about 11.5 kg per square metre: roughly 80 kg and 3.4 cm of headroom in a Fiat Ducato L3H2. Ply alone is 14 mm and 56 kg in poplar; a thick 30 mm PIR + 18 mm birch floor is 50 mm and 110 kg. The spread between the thinnest and thickest sensible floor is about 3.5 cm of standing height and 50 kg of payload.
Floor guides usually argue about materials. This one counts the two things the floor costs you, by van, and the one thing it has to do well: carry the furniture you screw into it.
The build-ups, in millimetres and kilograms
Weights use the densities VanPlot's build sheet uses — birch ply 680 kg/m³, poplar ply 450, XPS 33, PIR 31 — and 2.7 kg/m² for 2 mm sheet vinyl (manufacturer environmental declarations list 2.5–3.1 kg/m² for 2 mm vinyl, checked November 2026).
| Build-up | Layers | Thickness | kg/m², birch ply | kg/m², poplar ply |
|---|---|---|---|---|
| Ply only | 12 mm ply + 2 mm vinyl | 14 mm | 10.9 | 8.1 |
| Heavy-duty ply only | 18 mm ply + 2 mm vinyl | 20 mm | 14.9 | 10.8 |
| Foam + ply (floating) | 20 mm XPS + 12 mm ply + vinyl | 34 mm | 11.5 | 8.8 |
| Battens + foam + ply | 20 mm battens every 40 cm, XPS between, 12 mm ply, vinyl | 34 mm | 12.3 | 9.6 |
| Thick | 30 mm PIR + 18 mm ply + vinyl | 50 mm | 15.9 | 11.7 |
Three things fall out of the table:
- The insulation weighs almost nothing. 20 mm of XPS is 0.66 kg/m². The plywood is 70% of the floor's weight, and the vinyl is most of the rest. If you want a lighter floor, change the ply, not the foam.
- Battens cost weight, not height. They sit between the foam boards, in the same 20 mm, so the floor is no thicker — but 2.5 m of 45×20 mm timber per square metre adds about 0.9 kg/m². What they buy is something to screw into (see below).
- Poplar instead of birch saves 2.8 kg/m² at 12 mm. That is the biggest single weight lever in the floor, larger than leaving the insulation out entirely.
VanPlot's own "after build-up" figures — the finished heights in which vans you can stand up in and on every van page — subtract 40 mm for the floor: 20 mm insulation, 12 mm ply and a covering with some margin. If your floor is thinner, you gain the difference.
What it weighs in your van
Floor area here is the load-floor rectangle, length × width, from the same van database as the planner. The wheel arches sit inside that rectangle, so the ply you actually cut is a little less — treat these as the upper bound. Payload is the base van's rated payload before any build.
| Van | Load floor | Area | Ply only, poplar | Foam + 12 mm birch | Thick (PIR + 18 mm birch) | Payload | Thick floor, share of payload |
|---|---|---|---|---|---|---|---|
| VW Transporter T6.1 L2H2 | 2.85 × 1.70 m | 4.84 m² | 39 kg | 56 kg | 77 kg | 1075 kg | 7.2% |
| Renault Trafic L2H2 | 2.94 × 1.66 m | 4.88 m² | 40 kg | 56 kg | 77 kg | 1125 kg | 6.9% |
| Ford Transit Custom L2H2 | 2.92 × 1.78 m | 5.19 m² | 42 kg | 60 kg | 82 kg | 1044 kg | 7.9% |
| Fiat Ducato L2H2 | 3.12 × 1.87 m | 5.83 m² | 47 kg | 67 kg | 93 kg | 1480 kg | 6.3% |
| Ford Transit L3H3 FWD | 3.49 × 1.78 m | 6.22 m² | 50 kg | 72 kg | 99 kg | 1306 kg | 7.6% |
| Iveco Daily L3H2 | 3.54 × 1.80 m | 6.37 m² | 52 kg | 73 kg | 101 kg | 1140 kg | 8.9% |
| Renault Master L3H2 FWD | 3.73 × 1.77 m | 6.59 m² | 53 kg | 76 kg | 105 kg | 1280 kg | 8.2% |
| Fiat Ducato L3H2 | 3.71 × 1.87 m | 6.93 m² | 56 kg | 80 kg | 110 kg | 1405 kg | 7.8% |
| Fiat Ducato L4H2 | 4.07 × 1.87 m | 7.61 m² | 62 kg | 88 kg | 121 kg | 1265 kg | 9.5% |
| Mercedes Sprinter L3H2 RWD | 4.31 × 1.79 m | 7.70 m² | 62 kg | 89 kg | 122 kg | 1095 kg | 11.2% |
| VW Crafter L4H3 FWD | 4.30 × 1.83 m | 7.88 m² | 64 kg | 91 kg | 125 kg | 1151 kg | 10.9% |
| Mercedes Sprinter L4H2 RWD | 4.71 × 1.79 m | 8.41 m² | 68 kg | 97 kg | 133 kg | 1055 kg | 12.7% |
| VW Crafter L5H3 FWD | 4.86 × 1.83 m | 8.89 m² | 72 kg | 102 kg | 141 kg | 1084 kg | 13.0% |
The floor is one of the heaviest single items in a build — in a long Sprinter or Crafter a thick floor is an eighth of the payload before a single cabinet goes in. The long, heavy vans are also the ones with the least payload to spare, so the floor decision matters most exactly where the van is biggest. The rest of the weight budget is in how much a van conversion weighs and the payload guide.
What it costs in headroom
Every millimetre of floor comes off your standing height once. In a Fiat Ducato H2 (1.93 m raw interior height) with a 30 mm ceiling:
- ply only (14 mm): 1.89 m finished
- foam + ply (34 mm): 1.87 m
- VanPlot's 40 mm assumption: 1.86 m
- thick (50 mm): 1.85 m
Four centimetres sounds small until you are 1.84 m tall. If your height puts you within 3 cm of the ceiling in the standing-height table, the floor is where to take it back: the temperature difference through the floor is the smallest in the van, so thin floor insulation costs the least warmth per centimetre saved. The full trade between floor, walls and ceiling is in the insulation space-cost guide; how much insulation each surface needs is in how much insulation a campervan needs.
Going thinner, in order of what it costs you:
- 10 mm foam instead of 20 mm — 1 cm back, a little less warmth at your feet.
- 9 mm ply instead of 12 mm — 3 mm back and about 2 kg/m² lighter in birch, but screws hold less and the floor flexes more between supports.
- No foam at all — 2 cm back; fine for a summer van, cold underfoot in winter.
What it has to carry
Foam board is stronger than it looks. A 300 kPa XPS grade (for example Styrodur 3035 CS, per its datasheet: 300 kPa compressive stress at 10% deformation, checked November 2026) takes 30 tonnes per square metre before it squashes by a tenth; lighter 200 kPa grades are also sold. People walking on a floor never get near that. The problem is never the foam's total strength; it is point loads and fixings:
- A floating floor is a poor anchor. Plywood glued or laid on foam holds a screw only by its own thickness — 12 mm of thread. That is enough to locate a cabinet, not to hold a full kitchen or water tank in a hard stop. Fix heavy and tall units to the body as well: into the walls' ribs or furring, or down through the floor.
- Battens give the screw something to bite. With battens in the floor, furniture feet and floor fixings land on timber instead of foam. Mark the batten lines on the walls before the ply goes down, because you will not find them afterwards.
- Through-bolts for the heavy items. Water tanks, battery boxes, heaters and anything you would not want to meet at 50 km/h get bolts through to the steel floor (rivnuts or bolts with a load-spreading plate underneath), not wood screws into ply.
- Seats and seatbelts are not a floor question. They go on mounting points rated for them; the rules depend on your country and your registration. How many seats a camper van can have covers what that means for layout.
- Thicker ply where loads concentrate. A garage that carries bikes or a motorbike, or the strip under a heavy cabinet, is the place for 18 mm — not the whole floor. Lashing rails and eyes should be bolted into structure before the bed goes in; the garage dimensions guide has the details.
The floor is also the first thing to go in after wiring runs and before any furniture — the build order guide puts it in sequence. And the ply count for the subfloor is in the plywood sheets guide.
Check it in the planner
VanPlot has a floor build-up setting per project: set the floor thickness, and the 3D floor rises and every cabinet, bed and the standing-height check move with it, while the build sheet lists the foam, battens and subfloor ply with their weight added to the payload. Try 20 against 50 mm in your own van before you buy the boards — pick your van and start.
FAQ
How thick should a campervan floor be?
Most DIY floors are 30–40 mm: 20 mm of XPS or PIR board, a 12 mm plywood subfloor and a vinyl or click covering. VanPlot's height tables subtract 40 mm for the floor. Ply alone with vinyl is about 14 mm; a thick build with 30 mm PIR and 18 mm ply is about 50 mm.
What thickness of plywood should I use for a van floor?
12 mm is the usual subfloor and the thickness VanPlot's build sheet uses. 9 mm saves 3 mm of headroom and about 2 kg per square metre in birch, at the cost of screws that hold less. 18 mm is worth it under a garage or anywhere heavy loads concentrate; across a whole Ducato L3H2 it adds about 28 kg of birch over 12 mm.
How much does a van floor weigh?
About 11.5 kg per square metre for 20 mm XPS, 12 mm birch ply and 2 mm vinyl. On a Fiat Ducato L3H2 (6.93 m² load floor) that is about 80 kg. Poplar ply instead of birch brings it to about 61 kg; 30 mm PIR with 18 mm birch takes it to about 110 kg.
Do I need to insulate a campervan floor?
It is the least important surface. The temperature difference through the floor is the smallest in the van, so floor insulation mostly buys warm feet. If you are within a few centimetres of standing height, the floor is the first place to go thin.
Can I screw furniture into the plywood subfloor?
Light furniture, yes. Heavy or tall units — kitchen, wardrobe, water tank, battery box — should also be fixed to the body: into battens, through the floor to steel with bolts or rivnuts and load plates, or to the wall ribs. Seats and seatbelts never go on the subfloor; they belong on mounting points rated for them.
Related: insulation calculator · payload calculator